耐磨彩色混凝土地面和密封渗透剂的施工工艺

耐磨五颜六色混凝土地上 施工工艺，特点： 操作简便，降低成本。 面垫层及面层一次性施工，可进步地上整体性。 可防止地上空鼓等质量通病。适用范围：适用于各种工业、民用建筑及公共场所的大面积地上(如车库、坡道地上等)的施工。有耐磨等特殊要求的地上工程。工艺原理： 在初凝的混凝土外表上均匀的铺设特殊的矿藏骨料经压抹使其成为一个整体，从而取得厚度约2㎜且具有良好耐磨，防尘和美观性能的五颜六色耐磨地上。工艺流程和操作关键：工艺流程： 压实地基，模板设置，浇注砼 ，外表找平，撒布资料 圆盘作业 机械作业 机械板作 外表磨光作业 地上维护 收缩缝切

Abrasion-resistant colorful concrete ground construction technology, features: simple operation, cost reduction. One-time construction of surface cushion and surface layer can improve the integrity of the ground. It can prevent common quality faults such as overhead drum. Scope of application: It is suitable for the construction of large areas of industrial, civil buildings and public places (such as garages, ramps, etc.). Above ground works with special requirements such as wear resistance. Technological Principle: Uniform laying of special mineral aggregate on the surface of the initial setting concrete makes it a whole by pressing and plastering, thus obtaining a colorful wear-resistant ground with a thickness of about 2 feet and good wear-resistant, dust-proof and aesthetic properties. Process flow and key operation: process flow: compacting foundation, template setting, pouring concrete, surface leveling, disseminating data for the surface polishing operation of mechanical plate on the ground to maintain shrinkage slit cutting


密封浸透剂的施工工艺：清洁地上：使用专业推尘工具或洗地车将地上的垃圾、浮灰清洁洁净。部分修补：对于破损处合作地坪修补剂进行部分修补。粗磨地上：混凝土金属磨片30#50#120#配地坪研磨机对混凝土地上进行粗磨。根据地坪根底情况决定金属磨片起磨号数，意图是把混凝土地坪研磨平坦。喷涂或滚涂于地上上，坚持滋润4小时，期间用人工或机械办法拖动资料以帮助浸透，保证密封固化剂浸透深度。浸泡时刻达到要求后，清洗洁净任何残留的A剂。细磨地上：混凝土树脂片50#100#200#或软磨片(50#150#300#)进行混凝土地坪细磨。吸净水份，并晾干地上，利于B剂充沛浸透。涂刷B剂原液，浸泡时刻4小时，期间坚持湿润，保证密封固化剂深层充沛反响，形成有满足厚度的坚硬细密地坪聚硅层。精磨地上：混凝土树脂片400#或软磨片(500#1000#)精磨地上。抛光地上：混凝土抛光片800#1500#或软磨片(2000#3000#)抛光地坪，用尘推推净

Construction technology of sealing soaking agent: Clean the ground: Use professional dust pushing tools or floor washing trucks to clean the garbage and floating ash on the ground. Partial repairing: Partly repairing the damaged area with the cooperative floor repairing agent. Rough ground: concrete metal grinder 30 #50 #120 According to the condition of the ground floor, the number of metal grinding plates is determined. The purpose is to grind the concrete ground flat. Spraying or rolling on the ground, keep moistening for 4 hours, during which manual or mechanical methods are used to pull data to help soak, to ensure the depth of sealant solidification. After the soaking time reaches the requirement, clean any residual A agent. Fine ground: concrete resin 50 # 100 # 200 or soft ground (50 # 150 # 300) for fine grinding of concrete floor. Absorbing water and drying the ground are conducive to the abundant immersion of agent B. Brushing B agent solution, soaking time 4 hours, during which adhere to wet, to ensure that the deep sealant curing agent full response, the formation of a thick and compact floor polysilicon layer to meet the thickness. Precision ground: concrete resin sheet 400 or soft abrasive sheet (500 # 1000) fine ground. Polished floor: concrete polishing sheet 800 # 1500 # or soft abrasive sheet (2000 # 3000 #) polishing floor, push clean with dust

安徽环氧树脂自流平地坪官方网站：http://www.ahxxdp.com/